山东华全动力股份有限公司
山东华全动力股份有限公司
1. The design standard of the biogas unit is 20kW/25kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the voltage
1. The design standard of the biogas unit is 30kW/37.5kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the volta
1. The design standard of the biogas unit is 40kW/50kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the voltage
1. The design standard of the biogas unit is 150kW/187.5kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the vol
1. The design standard of the biogas unit is 100kW/125kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the volta
1. The design standard of the biogas unit is 100kW/125kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the volta
1. The design standard of the biogas unit is 100kW/125kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the volta
1. The design standard of the biogas unit is 100kW/125kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the volta
1. The design standard of the biogas unit is 100kW/125kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the volta
1. The design standard of the biogas unit is 100kW/125kVA, the voltage is 400V, the working frequency is 50Hz, and the power factor is 0.8 (lagging). The biogas engine can work in different methane gas concentration ranges (50-97%) or gas with the same calorific value, producing 100% electricity. 2. For the generator set running at normal operating temperature, the voltage, frequency change rate and engine recovery time conform to the ISO8528-5 standard, that is, to meet the 25% stepwise sudden load at the beginning, from the 25%-60% load stage Suddenly add 15% of the rated load, add 10% of the rated load from the 60%-80% load stage, and withstand 25% of the sudden load drop. Gas requirements： Fuel type Biogas Intake pressure 8Kpa-15Kpa, pressure change rate 1Kpa/min Methane content 55% Low calorific value (LHV) 25MJ/Nm3 Impurity particle size 5m, content 30mg/nm Sulfide 50mg/Nm3 Intake air temperature 40℃ Moisture content 40g/nm3 Note: Demineralized water should be used for the high and low temperature cycles of the engine, and the cooling water should be slightly alkaline clean water, and must not contain corrosive compounds such as chloride, sulfate or acid. The main index requirements are as follows ： Hardness 0.7～5.3me/L Chloride ion content 150mg/L PH value7～8.5 █ The generator is a synchronous generator, four-outlet, closed connection type, and the shrapnel is directly driven. The generator is equipped with a brushless rotating magnetic field. █ The generator should be closed and installed on the engine and the main rotor should be installed on the engine flywheel, using a flexible drive disc to ensure permanent alignment. █ The generator is an open waterproof drip design and is equipped with a protective device, manufactured according to IEE, NEMA MG-1-22 and IP23 standards, single bearing, raised electrode, rotating magnetic field, synchronous damping winding coil and 2/3 pitch The stator coil produces the most ideal voltage waveform. █ Protection level of forming winding and coastal climate, using vacuum pressure dipping process. The stator coil should be 2/3 pitch. The rotor and stator coils should be fully reinforced to withstand phase-to-phase and ground-to-phase failures. █ All insulation systems should be Class H of NEMA MG-1 standard. The stator has two dipping and drying (according to Class H insulation requirements). It is a solid-state electronic type, voltage/Hz type, three-phase voltage sensing to maintain the volta
Technical parameters of gas generator set Generator set model：HQRQ500GF Steady state voltage adjustment rate (%): 1 Generator power:500kW/625kVA Voltage fluctuation rate (%): 0.5 Power factor:COS = 0.8 (lagging) Transient voltage adjustment rate (%):＋20 ～－15 Output voltage:400V/230V Voltage stabilization time (s):1 Generator set current:900A Steady state frequency adjustment rate (%): 1 Rated frequency:50Hz Frequency fluctuation rate (%): 0.5 Rated speed:1500rpm Transient frequency adjustment rate (%):+ 10 ~ -7 Gas grade:LNG/CNG/Biogas Frequency stabilization time (S):3 Gas/Biogas generator size:3450*1390*1780 （L*W*H mm） Gas /biogas generator fuel consumption (100% load):0.6g/kWh Gas/Biogas generator weight:5000kg Diesel generator volume(LP7m):95dB（A） Technical parameters of diesel engine Gas/Biogas engines brand：Yuchai gas engine Cooling method: Closed water-cooling Gas/Biogas engines model: YC6C935N-D30 Oil supply method: direct injection Engine cylinder number: 6 / L Type Speed regulation method: ECU control Bore stroke: 145*165 mm Intake method: Natural inhalation Compression ratio: 11.5 ：1 Overload capacity: 110% Start method：DC 24V Electric start Diesel engines Speed: 1500rpm Technical parameters of generator Generator brand：Huaquan Brushless Generator Protection level：IP22 Generator Model：HQF-500 Wiring mode：Three-phase four-wire, Y-connection Generator power:500kW/625kVA Adjustment method: AVR (Automatic Voltage Regulator) Rated voltage: 400V / 230V Output frequency: 50Hz Insulation class: H class Output factor: COS = 0.8 (lag) Genset standard features 1)、Direct injection internal combustion engine( Gas/Biogas )； 2)、AC synchronous generator（Single Bearing）； 3)、Water Radiatordesign for 40-45℃ Ambient belt-driven fans and guards； 4)、Generation output air switch、Standard control panel； 5)、Steel common base with shock absorber； 6)、Dry-type air filterfuel filter，oil filter、starting motor、Self-charging alternator； 7)、starter battery and connecting cables； 8)、Industrial9dBmufflerand accessories； 9)、The engine and alternators original technical papers,manuals and testing reports ship with GenSet； Optional accessories（Extra charged） 1)、Engine oil、diesel、water jacket、Anti-condensation heater 2)、Battery floating charger 3)、Self-protection unit/self-starting control panel 4)、Tree-remote control panel 5)、ATS AUTO-loadedtransferringscreen 6)、Daily fuel tank、In
Technical parameters of gas generator set Generator set model：HQRQ360GF Steady state voltage adjustment rate (%): 1 Generator power:360kW/450kVA Voltage fluctuation rate (%): 0.5 Power factor:COS = 0.8 (lagging) Transient voltage adjustment rate (%):＋20 ～－15 Output voltage:400V/230V Voltage stabilization time (s):1 Generator set current:649.5A Steady state frequency adjustment rate (%): 1 Rated frequency:50Hz Frequency fluctuation rate (%): 0.5 Rated speed:1500rpm Transient frequency adjustment rate (%):+ 10 ~ -7 Gas grade:LNG/CNG/Biogas Frequency stabilization time (S):3 Gas/Biogas generator size:3000*1050*1700 （L*W*H mm） Gas /biogas generator fuel consumption (100% load):0.6g/kWh Gas/Biogas generator weight:2800kg Diesel generator volume(LP7m):95dB（A） Technical parameters of diesel engine Gas/Biogas engines brand：Yuchai gas engine Cooling method: Closed water-cooling Gas/Biogas engines model: YC6T350NL-D20 Oil supply method: direct injection Engine cylinder number: 6 / L Type Speed regulation method: ECU control Bore stroke: 145*165 mm Intake method: Natural inhalation Compression ratio: 11.5 ：1 Overload capacity: 110% Start method：DC 24V Electric start Diesel engines Speed: 1500rpm Technical parameters of generator Generator brand：Huaquan Brushless Generator Protection level：IP22 Generator Model：HQF-100 Wiring mode：Three-phase four-wire, Y-connection Generator power:100kW/125kVA Adjustment method: AVR (Automatic Voltage Regulator) Rated voltage: 400V / 230V Output frequency: 50Hz Insulation class: H class Output factor: COS = 0.8 (lag) Genset standard features 1)、Direct injection internal combustion engine( Gas/Biogas )； 2)、AC synchronous generator（Single Bearing）； 3)、Water Radiatordesign for 40-45℃ Ambient belt-driven fans and guards； 4)、Generation output air switch、Standard control panel； 5)、Steel common base with shock absorber； 6)、Dry-type air filterfuel filter，oil filter、starting motor、Self-charging alternator； 7)、starter battery and connecting cables； 8)、Industrial9dBmufflerand accessories； 9)、The engine and alternators original technical papers,manuals and testing reports ship with GenSet； Optional accessories（Extra charged） 1)、Engine oil、diesel、water jacket、Anti-condensation heater 2)、Battery floating charger 3)、Self-protection unit/self-starting control panel 4)、Tree-remote control panel 5)、ATS AUTO-loadedtransferringscreen 6)、Daily fuel tank、
Weifang, shandong province, China 中国 山东。潍坊
Shandong Huaquan Power Co., Ltd.
Permanent copyright